The following article addresses general connection and noise issues when using the DUO-CAPTURE EX with a computer:
-
Be sure to install the driver for your operating system. You may download the driver from the link below:
DUO-CAPTURE EX Downloads - Be sure that the COMPUTER tab on the back of the DUO-CAPTURE EX is set to either "44.1" or "48" and not "TAB". When the DUO-CAPTURE EX is set to TAB, the driver modes are ignored and the interface is setup to be connected to a tablet (i.e. iPad). If this needs to be changed, close down all software, turn off the DUO-CAPTURE EX, change the switch to 44.1 or 48 and then power DUO-CAPTURE EX back on.
- If you're using a power supply, be sure that you're using a PSB-1U or PSB-120 power supply only--3rd party power supplies can cause the unit to not operate properly. If you are using batteries, try using brand new, unused batteries for troubleshooting purposes--Alkaline batteries are recommended.
-
Be sure to log on as a user with administrative privileges on your computer.
-
Close/turn off system monitoring/anti-virus software when installing the driver--such as the Norton software you have installed. If system monitoring software such as anti-virus programs are installed on your computer, close them while troubleshooting.
-
Connect directly to your computer via USB. Do not connect to a USB hub while troubleshooting.
-
Be sure that you are connecting to a USB 2.0 port on your computer; or a USB 3.0 port with backwards compatibility. Check the USB 3.0 specifications of your computer to determine if there is complete support for USB backwards compatibility.
- Try a different USB cable.
- Try different USB ports on the computer.
- Uninstall and then reinstall the driver: https://www.roland.com/global/products/duo-capture_ex/downloads/
- Raise the buffer setting of both the DUO-CAPTURE EX as well as the audio software (DAW) being used:
DUO-CAPTURE EX: Adjusting Buffer -
Try disconnecting the DUO-CAPTURE EX from the computer, running the uninstall program that came with the driver download, restarting the computer and then installing.
-
Install the latest version of Windows or Mac OS X:
- Install the latest version of the DAW audio software being used.
-
If you're using Windows, install the latest Service Pack for Windows.
-
Did you install a device, install software or a plug-in, or make a change in Device Manager just before the issue appeared? If so, it's possible that the change you made caused the connection or noise issue.
Undo the change or uninstall the driver or software (if you can), restart your PC, and then troubleshoot. Depending on the changes you made, some solutions might include:
- Remove or reconfigure the newly installed device.
- Roll back the driver to a version prior to your update.
- Use System Restore to undo recent changes. - Scan for viruses or trojans with any antivirus software installed.
-
Check Power Management Settings (Windows only):
a. Click on the Windows (or Start) icon on the bottom left of your screen.
b. Select Control Panel. The Control Panel window will appear.
c. On the top-right of the Control Panel window, set the “View by:” to “Small Icons”.
d. Click on "Power Options."
e. In "Choose or customize a power plan," select "High performance" or "Show additional plans."
f. In the High performance area, click "Change plan settings."
g. Click "Change advanced power settings."
h. In the Advanced Settings, click the “+” symbol for "Hard Disk," and click the “+”symbol for "Turn off hard disk after" to open it.
i. Click "Setting (Minutes)," and click the down arrow to change the setting to "Never."
j. Click [OK] to close the Power Options window.
k. Close the "Edit Plan Settings" screen. -
Check Performance Options settings (Windows only):
a. Open "Control Panel," click "System and Security " or "System and Maintenance," and then click "System." If the Control Panel is in the icon view or Classic View, then double-click the "System" icon
b. At the left, click "Advanced system settings."
c. If a dialog box regarding User Account Control appears, click [Yes] or [Continue]. If you are asked to enter the password of an Administrator account, log on to Windows as a user whose Account Type is Administrator, then perform the settings again.
d. Click [Settings] of the Performance section, and then click the [Advanced] tab.
e. Select "Background services," and click [OK].
f. Click [OK] to close "System Properties." - Contact the computer manufacturer and see if you can get an updated USB driver/controller installed--as a new version from the manufacturer may resolve USB issues with the computer you're using.
- Test with another DAW audio software to determine if the issue is with the DUO-CAPTURE EX or the software being used. If the problem does not continue with another DAW audio software, then contact the software manufacturer to troubleshoot the issue.